Bookworm. Pi 4B
.....
Setting up mesa-vulkan-drivers:arm64 (23.2.1-1~bpo12+rpt3) ...
Setting up mesa-vdpau-drivers:arm64 (23.2.1-1~bpo12+rpt3) ...
Setting up firmware-atheros (1:20230210-5+rpt3) ...
Setting up firmware-misc-nonfree (1:20230210-5+rpt3) ...
Setting up linux-libc-dev:arm64 (1:6.1.73-1+rpt1) ...
Setting up libkms++0:arm64 (0~git20231115~065257+9ae90ce-1) ...
Setting up firmware-brcm80211 (1:20230210-5+rpt3) ...
Setting up firmware-realtek (1:20230210-5+rpt3) ...
Setting up raspi-firmware (1:1.20231024+ds-1+rpt5) ...
Installing new version of config file /etc/default/raspi-firmware ... Installing new version of config file /etc/initramfs/post-update.d/z50-raspi-firmware ...
Installing new version of config file
/etc/kernel/postinst.d/z50-raspi-firmware ...


and here it sits. I cant ssh into it. It's bricked itself AGAIN

Last time I power cycled it, when this happened it wouldn't boot at all.


I've plugged an HDMI screen and key board into it and it shows the boot sequence and something about a disk drive aborted journal...detected by
systemd and apt-get

Is there any hope or do I reinstall all over AGAIN.

And how to stop it happening again.



--
If you tell a lie big enough and keep repeating it, people will
eventually come to believe it. The lie can be maintained only for such
time as the State can shield the people from the political, economic
and/or military consequences of the lie. It thus becomes vitally
important for the State to use all of its powers to repress dissent, for
the truth is the mortal enemy of the lie, and thus by extension, the
truth is the greatest enemy of the State.

Joseph Goebbels

--- SoupGate-Win32 v1.05
* Origin: Agency HUB, Dunedin - New Zealand | Fido<>Usenet Gateway (3:770/3)

On 01.02.2024 21:17, The Natural Philosopher wrote:

Bookworm. Pi 4B
.....
Setting up mesa-vulkan-drivers:arm64 (23.2.1-1~bpo12+rpt3) ...
Setting up mesa-vdpau-drivers:arm64 (23.2.1-1~bpo12+rpt3) ...
Setting up firmware-atheros (1:20230210-5+rpt3) ...
Setting up firmware-misc-nonfree (1:20230210-5+rpt3) ...
Setting up linux-libc-dev:arm64 (1:6.1.73-1+rpt1) ...
Setting up libkms++0:arm64 (0~git20231115~065257+9ae90ce-1) ...
Setting up firmware-brcm80211 (1:20230210-5+rpt3) ...
Setting up firmware-realtek (1:20230210-5+rpt3) ...
Setting up raspi-firmware (1:1.20231024+ds-1+rpt5) ...
Installing new version of config file /etc/default/raspi-firmware ... Installing new version of config file /etc/initramfs/post-update.d/z50-raspi-firmware ...
Installing new version of config file /etc/kernel/postinst.d/z50-raspi-firmware ...

and here it sits. I cant ssh into it. It's bricked itself AGAIN

Last time I power cycled it, when this happened it wouldn't boot at all.

I've plugged an HDMI screen and key board into it and it shows the boot sequence and something about a disk drive aborted journal...detected by systemd and apt-get

Is there any hope or do I reinstall all over AGAIN.

And how to stop it happening again.

You boot from card or USB?
I never faced that error. Maybe a hw problem with the card ...

--- SoupGate-Win32 v1.05
* Origin: Agency HUB, Dunedin - New Zealand | Fido<>Usenet Gateway (3:770/3)

On 01/02/2024 19:17, The Natural Philosopher wrote:

Bookworm. Pi 4B
.....
Setting up mesa-vulkan-drivers:arm64 (23.2.1-1~bpo12+rpt3) ...
Setting up mesa-vdpau-drivers:arm64 (23.2.1-1~bpo12+rpt3) ...
Setting up firmware-atheros (1:20230210-5+rpt3) ...
Setting up firmware-misc-nonfree (1:20230210-5+rpt3) ...
Setting up linux-libc-dev:arm64 (1:6.1.73-1+rpt1) ...
Setting up libkms++0:arm64 (0~git20231115~065257+9ae90ce-1) ...
Setting up firmware-brcm80211 (1:20230210-5+rpt3) ...
Setting up firmware-realtek (1:20230210-5+rpt3) ...
Setting up raspi-firmware (1:1.20231024+ds-1+rpt5) ...
Installing new version of config file /etc/default/raspi-firmware ... Installing new version of config file /etc/initramfs/post-update.d/z50-raspi-firmware ...
Installing new version of config file /etc/kernel/postinst.d/z50-raspi-firmware ...

and here it sits. I cant ssh into it. It's bricked itself AGAIN

Last time I power cycled it, when this happened it wouldn't boot at all.

I've plugged an HDMI screen and key board into it and it shows the boot sequence and something about a disk drive aborted journal...detected by systemd and apt-get

Is there any hope or do I reinstall all over AGAIN.

And how to stop it happening again.

It's come up with another message on the remote terminal

sync: error syncing '/boot/firmware/LICENCE.broadcom': Input/output error

The HDMI console is saying read error on swap device

read error reading directory iblock 0

On the other disk I think.

(it has two SSDs and no SD card)

Photo of HDMI console

http://vps.templar.co.uk/Softwarebugs/20240201_192653.jpg

I will leave it on as I am scared to reboot it..last time it didn't



--
How fortunate for governments that the people they administer don't think.

Adolf Hitler

--- SoupGate-Win32 v1.05
* Origin: Agency HUB, Dunedin - New Zealand | Fido<>Usenet Gateway (3:770/3)

On 01/02/2024 19:21, LucLan wrote:

On 01.02.2024 21:17, The Natural Philosopher wrote:

Bookworm. Pi 4B
.....
Setting up mesa-vulkan-drivers:arm64 (23.2.1-1~bpo12+rpt3) ...
Setting up mesa-vdpau-drivers:arm64 (23.2.1-1~bpo12+rpt3) ...
Setting up firmware-atheros (1:20230210-5+rpt3) ...
Setting up firmware-misc-nonfree (1:20230210-5+rpt3) ...
Setting up linux-libc-dev:arm64 (1:6.1.73-1+rpt1) ...
Setting up libkms++0:arm64 (0~git20231115~065257+9ae90ce-1) ...
Setting up firmware-brcm80211 (1:20230210-5+rpt3) ...
Setting up firmware-realtek (1:20230210-5+rpt3) ...
Setting up raspi-firmware (1:1.20231024+ds-1+rpt5) ...
Installing new version of config file /etc/default/raspi-firmware ...
Installing new version of config file
/etc/initramfs/post-update.d/z50-raspi-firmware ...
Installing new version of config file
/etc/kernel/postinst.d/z50-raspi-firmware ...


and here it sits. I cant ssh into it. It's bricked itself AGAIN

Last time I power cycled it, when this happened it wouldn't boot at all.


I've plugged an HDMI screen and key board into it and it shows the
boot sequence and something about a disk drive aborted
journal...detected by systemd and apt-get

Is there any hope or do I reinstall all over AGAIN.

And how to stop it happening again.

You boot from card or USB?
I never faced that error. Maybe a hw problem with the card ...

USB booting. Two SSDs - one to boot, one for data. Data one is never
used normally - its a test setup for a new NAS and its not in any sort
of use.

But errors on both drives are showing up

--
Microsoft : the best reason to go to Linux that ever existed.

--- SoupGate-Win32 v1.05
* Origin: Agency HUB, Dunedin - New Zealand | Fido<>Usenet Gateway (3:770/3)

On 01.02.2024 21:31, The Natural Philosopher wrote:

On 01/02/2024 19:17, The Natural Philosopher wrote:

Bookworm. Pi 4B
.....
Setting up mesa-vulkan-drivers:arm64 (23.2.1-1~bpo12+rpt3) ...
Setting up mesa-vdpau-drivers:arm64 (23.2.1-1~bpo12+rpt3) ...
Setting up firmware-atheros (1:20230210-5+rpt3) ...
Setting up firmware-misc-nonfree (1:20230210-5+rpt3) ...
Setting up linux-libc-dev:arm64 (1:6.1.73-1+rpt1) ...
Setting up libkms++0:arm64 (0~git20231115~065257+9ae90ce-1) ...
Setting up firmware-brcm80211 (1:20230210-5+rpt3) ...
Setting up firmware-realtek (1:20230210-5+rpt3) ...
Setting up raspi-firmware (1:1.20231024+ds-1+rpt5) ...
Installing new version of config file /etc/default/raspi-firmware ...
Installing new version of config file
/etc/initramfs/post-update.d/z50-raspi-firmware ...
Installing new version of config file
/etc/kernel/postinst.d/z50-raspi-firmware ...


and here it sits. I cant ssh into it. It's bricked itself AGAIN

Last time I power cycled it, when this happened it wouldn't boot at all.


I've plugged an HDMI screen and key board into it and it shows the
boot sequence and something about a disk drive aborted
journal...detected by systemd and apt-get

Is there any hope or do I reinstall all over AGAIN.

And how to stop it happening again.

It's come up with another message on the remote terminal

sync: error syncing '/boot/firmware/LICENCE.broadcom': Input/output error

The HDMI console is saying read error on swap device

read error reading directory iblock 0

On the other disk I think.

(it has two SSDs and no SD card)

Photo of HDMI console

http://vps.templar.co.uk/Softwarebugs/20240201_192653.jpg

I will leave it on as I am scared to reboot it..last time it didn't

for me looks like a hw error

--- SoupGate-Win32 v1.05
* Origin: Agency HUB, Dunedin - New Zealand | Fido<>Usenet Gateway (3:770/3)

On 01/02/2024 19:38, The Natural Philosopher wrote:

On 01/02/2024 19:21, LucLan wrote:

On 01.02.2024 21:17, The Natural Philosopher wrote:

Bookworm. Pi 4B
.....
Setting up mesa-vulkan-drivers:arm64 (23.2.1-1~bpo12+rpt3) ...
Setting up mesa-vdpau-drivers:arm64 (23.2.1-1~bpo12+rpt3) ...
Setting up firmware-atheros (1:20230210-5+rpt3) ...
Setting up firmware-misc-nonfree (1:20230210-5+rpt3) ...
Setting up linux-libc-dev:arm64 (1:6.1.73-1+rpt1) ...
Setting up libkms++0:arm64 (0~git20231115~065257+9ae90ce-1) ...
Setting up firmware-brcm80211 (1:20230210-5+rpt3) ...
Setting up firmware-realtek (1:20230210-5+rpt3) ...
Setting up raspi-firmware (1:1.20231024+ds-1+rpt5) ...
Installing new version of config file /etc/default/raspi-firmware ...
Installing new version of config file
/etc/initramfs/post-update.d/z50-raspi-firmware ...
Installing new version of config file
/etc/kernel/postinst.d/z50-raspi-firmware ...


and here it sits. I cant ssh into it. It's bricked itself AGAIN

Last time I power cycled it, when this happened it wouldn't boot at all. >>>

I've plugged an HDMI screen and key board into it and it shows the
boot sequence and something about a disk drive aborted
journal...detected by systemd and apt-get

Is there any hope or do I reinstall all over AGAIN.

And how to stop it happening again.

You boot from card or USB?
I never faced that error. Maybe a hw problem with the card ...

USB booting.  Two SSDs - one to boot, one for data. Data one is never
used normally - its a test setup for a new NAS and its not in any sort
of use.

But errors on both  drives are showing up

More errors

dpkg: error processing package raspi-firmware (--configure):
installed raspi-firmware package post-installation script subprocess
returned error exit status 1
Setting up libglapi-mesa:arm64 (23.2.1-1~bpo12+rpt3) ...
dpkg: unrecoverable fatal error, aborting:
unable to truncate for updated status of 'libglapi-mesa:arm64':
Read-only file system
E: Sub-process /usr/bin/dpkg returned an error code (2)
W: Operation was interrupted before it could finish
W: Problem unlinking the file /var/cache/apt/pkgcache.bin -
pkgDPkgPM::Go (30: Read-only file system)


--
Socialism is the philosophy of failure, the creed of ignorance and the
gospel of envy.

Its inherent virtue is the equal sharing of misery.

Winston Churchill

--- SoupGate-Win32 v1.05
* Origin: Agency HUB, Dunedin - New Zealand | Fido<>Usenet Gateway (3:770/3)

On 01/02/2024 19:31, The Natural Philosopher wrote:

On 01/02/2024 19:17, The Natural Philosopher wrote:

Bookworm. Pi 4B
.....
Setting up mesa-vulkan-drivers:arm64 (23.2.1-1~bpo12+rpt3) ...
Setting up mesa-vdpau-drivers:arm64 (23.2.1-1~bpo12+rpt3) ...
Setting up firmware-atheros (1:20230210-5+rpt3) ...
Setting up firmware-misc-nonfree (1:20230210-5+rpt3) ...
Setting up linux-libc-dev:arm64 (1:6.1.73-1+rpt1) ...
Setting up libkms++0:arm64 (0~git20231115~065257+9ae90ce-1) ...
Setting up firmware-brcm80211 (1:20230210-5+rpt3) ...
Setting up firmware-realtek (1:20230210-5+rpt3) ...
Setting up raspi-firmware (1:1.20231024+ds-1+rpt5) ...
Installing new version of config file /etc/default/raspi-firmware ...
Installing new version of config file
/etc/initramfs/post-update.d/z50-raspi-firmware ...
Installing new version of config file
/etc/kernel/postinst.d/z50-raspi-firmware ...


and here it sits. I cant ssh into it. It's bricked itself AGAIN

Last time I power cycled it, when this happened it wouldn't boot at all.


I've plugged an HDMI screen and key board into it and it shows the
boot sequence and something about a disk drive aborted
journal...detected by systemd and apt-get

Is there any hope or do I reinstall all over AGAIN.

And how to stop it happening again.

It's come up with another message on the remote terminal

sync: error syncing '/boot/firmware/LICENCE.broadcom': Input/output error

The HDMI console is saying read error on swap device

read error reading directory iblock 0

On the other disk I think.

(it has two SSDs and no SD card)

Photo of HDMI console

http://vps.templar.co.uk/Softwarebugs/20240201_192653.jpg

I will leave it on as I am scared to reboot it..last time it didn't

Well as per last time it eventually settled to bricked and totally unresponsive.

I power cycled it and now all it can say is 'Firmware not found'.

So the upgrade has once again royally fucked it.
Any ideas?



--
The lifetime of any political organisation is about three years before
its been subverted by the people it tried to warn you about.

Anon.

--- SoupGate-Win32 v1.05
* Origin: Agency HUB, Dunedin - New Zealand | Fido<>Usenet Gateway (3:770/3)

On 01/02/2024 19:40, LucLan wrote:

On 01.02.2024 21:31, The Natural Philosopher wrote:

On 01/02/2024 19:17, The Natural Philosopher wrote:

Bookworm. Pi 4B
.....
Setting up mesa-vulkan-drivers:arm64 (23.2.1-1~bpo12+rpt3) ...
Setting up mesa-vdpau-drivers:arm64 (23.2.1-1~bpo12+rpt3) ...
Setting up firmware-atheros (1:20230210-5+rpt3) ...
Setting up firmware-misc-nonfree (1:20230210-5+rpt3) ...
Setting up linux-libc-dev:arm64 (1:6.1.73-1+rpt1) ...
Setting up libkms++0:arm64 (0~git20231115~065257+9ae90ce-1) ...
Setting up firmware-brcm80211 (1:20230210-5+rpt3) ...
Setting up firmware-realtek (1:20230210-5+rpt3) ...
Setting up raspi-firmware (1:1.20231024+ds-1+rpt5) ...
Installing new version of config file /etc/default/raspi-firmware ...
Installing new version of config file
/etc/initramfs/post-update.d/z50-raspi-firmware ...
Installing new version of config file
/etc/kernel/postinst.d/z50-raspi-firmware ...


and here it sits. I cant ssh into it. It's bricked itself AGAIN

Last time I power cycled it, when this happened it wouldn't boot at all. >>>

I've plugged an HDMI screen and key board into it and it shows the
boot sequence and something about a disk drive aborted
journal...detected by systemd and apt-get

Is there any hope or do I reinstall all over AGAIN.

And how to stop it happening again.

It's come up with another message on the remote terminal

sync: error syncing '/boot/firmware/LICENCE.broadcom': Input/output error

The HDMI console is saying read error on swap device

read error reading directory iblock 0

On the other disk I think.

(it has two SSDs and no SD card)

Photo of HDMI console

http://vps.templar.co.uk/Softwarebugs/20240201_192653.jpg

I will leave it on as I am scared to reboot it..last time it didn't

for me looks like a hw error

On BOTH USB drives?
and ONLY when upgrading?

Hmm.

--
Socialism is the philosophy of failure, the creed of ignorance and the
gospel of envy.

Its inherent virtue is the equal sharing of misery.

Winston Churchill

--- SoupGate-Win32 v1.05
* Origin: Agency HUB, Dunedin - New Zealand | Fido<>Usenet Gateway (3:770/3)

On 01/02/2024 19:17, The Natural Philosopher wrote:

Bookworm. Pi 4B
.....
Setting up mesa-vulkan-drivers:arm64 (23.2.1-1~bpo12+rpt3) ...
Setting up mesa-vdpau-drivers:arm64 (23.2.1-1~bpo12+rpt3) ...
Setting up firmware-atheros (1:20230210-5+rpt3) ...
Setting up firmware-misc-nonfree (1:20230210-5+rpt3) ...
Setting up linux-libc-dev:arm64 (1:6.1.73-1+rpt1) ...
Setting up libkms++0:arm64 (0~git20231115~065257+9ae90ce-1) ...
Setting up firmware-brcm80211 (1:20230210-5+rpt3) ...
Setting up firmware-realtek (1:20230210-5+rpt3) ...
Setting up raspi-firmware (1:1.20231024+ds-1+rpt5) ...
Installing new version of config file /etc/default/raspi-firmware ... Installing new version of config file /etc/initramfs/post-update.d/z50-raspi-firmware ...
Installing new version of config file /etc/kernel/postinst.d/z50-raspi-firmware ...

and here it sits. I cant ssh into it. It's bricked itself AGAIN

Last time I power cycled it, when this happened it wouldn't boot at all.

I've plugged an HDMI screen and key board into it and it shows the boot sequence and something about a disk drive aborted journal...detected by systemd and apt-get

Is there any hope or do I reinstall all over AGAIN.

And how to stop it happening again.

To cut a long story short, the upgrade totally wiped out the rootfs -
its not even recognised as a *partition* any more - and the bootfs is
looking a bit sick as well.


Thank you, bookworm.

Is it worth even continuing??

--
For in reason, all government without the consent of the governed is the
very definition of slavery.

Jonathan Swift

--- SoupGate-Win32 v1.05
* Origin: Agency HUB, Dunedin - New Zealand | Fido<>Usenet Gateway (3:770/3)

The Natural Philosopher <tnp@invalid.invalid> writes:

On 01/02/2024 19:40, LucLan wrote:

On 01.02.2024 21:31, The Natural Philosopher wrote:

Photo of HDMI console

http://vps.templar.co.uk/Softwarebugs/20240201_192653.jpg

Something has scrambled the disk contents.

I will leave it on as I am scared to reboot it..last time it didn't

for me looks like a hw error

On BOTH USB drives?

Or the board itself.

and ONLY when upgrading?

Upgrades involve much more CPU and IO (and therefore waste heat) than
many other use cases - I could easily believe in a hardware fault that
only surfaces during upgrades.

--
https://www.greenend.org.uk/rjk/

--- SoupGate-Win32 v1.05
* Origin: Agency HUB, Dunedin - New Zealand | Fido<>Usenet Gateway (3:770/3)

On 02/02/2024 09:05, Richard Kettlewell wrote:

Upgrades involve much more CPU and IO (and therefore waste heat) than
many other use cases - I could easily believe in a hardware fault that
only surfaces during upgrades.

in both cases the crash happened at exactly the same place in the same
upgrade

I discovered a few more points: That upgrade problem is not unique to
me. In most cases people who did that upgrade and had a problem suffered
a complete loss of the /boot/firmware directory.

I haven't got chapter and verse but the common factor seems to be
upgrading from a previous version to the Dec 2023 version using apt-get upgrade..

I discovered why my December 2023 version didn't install, as well. It
was corrupted somehow. It wouldn't mount. I re-downloaded it,
re-installed it and that finally did boot, but there were strange file
and read errors when I attached the *second* disk to the system. But a
reboot cured *that*.

The system upgraded perfectly well once the new OS image was installed.

Perhaps the power supply is inadequate?
I don't know

At the moment I have rebuilt to about the same point the development
system was when it bricked

I've checked the disks with smartctl and there are no errors logged.

So the problem would seem to be with the pi itself or the OS. or some
other part of the hardware.




--
“But what a weak barrier is truth when it stands in the way of an hypothesis!”

Mary Wollstonecraft

--- SoupGate-Win32 v1.05
* Origin: Agency HUB, Dunedin - New Zealand | Fido<>Usenet Gateway (3:770/3)